IntensaFIRE Controller Mods for Xbox 360 and PlayStation 3

Fastest & Easiest Xbox 360 and PlayStation 3 Controller Mods

I need assistance

So I tried installing the intensafire to my xbox 360 controller. unfortunatly, I had a lot of trouble with the glue. when I tested my controller, as soon as I pressed the sync button, my controller started firing automatically, and continued after reloading. also, my left trigger sometimes doesnt work. what should i do? and how can I remove the glue so I can try again?

Views: 9

▶ Reply to This

Replies to This Discussion

Permalink Reply by Patrick Mason on June 30, 2010 at 12:47pm
You most likely used too much glue and did not let the glue sit for a few hours. You can remove the glue with nail polish remover and a q-tip.
Permalink Reply by Ryan Carr on June 30, 2010 at 12:48pm
I used a blowdryer on the glue, but maybe I did use too much. ill try removing it.
Permalink Reply by Patrick Mason on June 30, 2010 at 12:50pm
I would suggest not using a blow dryer on it and let it air dry without the shell put back on for atleast 2 hours. Also, try to use a minimal amount of glue.
Permalink Reply by Ryan Carr on June 30, 2010 at 1:20pm
my middle grounding point part of the flex board will not stay down, even if i try to push it. I feel like the ring is too small. any suggestions?
Permalink Reply by David on June 30, 2010 at 3:59pm
i had this when i got my Intensafire so wot i did removed the glue with nail remover and q-tip so then after 5 gos with the glue i got the old Soldering iron out n used that had no probs with it after that n then sold to a friend i do recommend Soldering it to anyone it so easy to do it and saves alot of time

sorry for messed up typing lol
Permalink Reply by Ryan Carr on June 30, 2010 at 6:58pm
I tried gluing again, but now my right trigger doesnt work, even without the mod on. also, I didnt connect the sync correctly so I dont know if that is affecting the trigger. What could be causing my trigger to not work while the mod is off? there is definitly not too much glue
Permalink Reply by Dan Greffe on June 30, 2010 at 7:40pm
post a pic of the controller board and we can help. the most likely problem is glue on a chip, dont worry tho, theres a solution to that!! just post a high res. pic and we can all help.
Permalink Reply by Joseph FRAZEY on July 1, 2010 at 12:33am
Yeah i have one that when and ONLY when i have akimbo mode on it shoots realllly fast and my guy sprints then runs in a circle while tapping the left trigger furiously! I though about fixing it but its pretty neat for when you go AFK but i have many controllers you sir only have one so please send us a picture before you fry your motherboard!
Permalink Reply by Dan Greffe on July 1, 2010 at 1:11am
yeah its sure nice to have an arsenal of controllers i have enough to host whole lan parties, but then again i also have enough 360's to do that aswell... one of the most interesting controllers i have is the datel rapidfire. it has turbo programmable for all face buttons and bumbers. not too sure about using it online becuz of some rumours i heard about microsoft bannig users for the controller online due to an odd feedback the controller has from being third party. actually the company got sued i think but the controlllers are still for sale!!! believe it or not this is one of the greatest controllers for the 360, other than it inability to be used online! i totally recommend it for offline campaign modes for ALL games! you all just gotta have one of these!! plus it also has some extra lights on the side!! neat!!

Joseph FRAZEY said:
Yeah i have one that when and ONLY when i have akimbo mode on it shoots realllly fast and my guy sprints then runs in a circle while tapping the left trigger furiously! I though about fixing it but its pretty neat for when you go AFK but i have many controllers you sir only have one so please send us a picture before you fry your motherboard!
Permalink Reply by Ryan Carr on July 1, 2010 at 3:43am
Alright. I will post a picture today soon. I fixed the glue on the sync button, so the mod can turn on now, but my right trigger does not work without the mod, and it will fire by itself when I turn on the mod. It's like the right trigger is stuck down, but its not.
Permalink Reply by Ryan Carr on July 1, 2010 at 4:10am
Permalink Reply by Ryan Carr on July 1, 2010 at 6:58am
Alright guys, so there was a tiny bit of glue bridging the right trigger. that solvred my problems. now i just need advice on how to keep the sync connection glued on my matrix. this mod is great, thanks for the support!

▶ Reply to Discussion

RSS

Xbox 360 IntensaFIRE

© 2012   Created by Team IntensaFIRE.   Powered by

Badges  |  Report an Issue  |  Terms of Service